Loading...
HomeMy WebLinkAboutSD-20-02 - Supplemental - 0010 Mansfield View Lane (11)LUMINAIRE SCHEDULE Civil Engineering Associates 12/18/2019 Type Catalog Number Description Lamp Pole Height Notes Quantity A S5e 35-40L Kim Lighting 1SA- SAR5-P35-40L-4K-120-DB- A25-7 with pole-P/PRA16- 4188SA/DB-P Single arm Type 5 cutoff luminaire at 20' AFG mounting height 46w LED PicoPrism, 5352 lumens, 4000K 20'Controlled by photorectacle and timed off by programmed timer 1 B 2S3p35-40L Kim Lighting 2SB-SAR3-P35-40L-4K-120- DB-A25-7 with pole- P/PRA20-4188SA/DB-P Double arm Type 3 cutoff luminaire at 20' AFG mounting height 2 x 46w LED PicoPrism, 5200 lumens x 2, 4000K 20'Controlled by photorectacle and timed off by programmed timer 1 C S3p35-40L Kim Lighting 1SA- SAR3-P35-40L-4K-120-DB- A25-7 with pole-P/PRA20- 4188SA/DB-P Single arm Type 3 cutoff luminaire at 20' AFG mounting height 46w LED PicoPrism, 5200 lumens, 4000K 20'Controlled by photorectacle and timed off by programmed timer 2 D SL1 Kim Lighting SL1-18L-4K-UV Light bollard with cutoff optics at 371/2" light center and 42" overall height LED mid power LED replaceable modules 42" overall bollard height On/off controlled by programmed timer 7 E RL56 Halo RL560WH9930 LED module with H2750ICAT new construction housing Recessed LED soffit light 13.5w LED, 900 lumens, 90 CRI, 4000K 9' ceiling mounted at porches Exterior wet location rated 4 Control Notes: Hinesburg Road, So. Burlington, VT 1. Site lighting shall be activated by photocell and shall be turned off by programmable timer located inside building. 2. Provide occupancy sensor control for bollard lighting with 15 minute delay after motion is no longer detected. 3. Provide program scheduled on/off control for porch lighting with manual interior override control. | 1 | JOB NOTES TYPE APPROVALS SAR The Archetype® Small PicoPrism LED kl_sarpled_spec.pdf Kim Lighting reserves the right to change specifications without notice. © 2017 KIM LIGHTING | 17760 Rowland Street | City of Industry | CA 91748 P 626.968.5666 | F 626.369.2695 | www.kimlighting.com | Rev. Apr 23, 2019 SPECIFICATIONS ORDERING CODE FEATURES Certifications ■ PicoPrism® technology1 ■ Full uplight cutoff ■ Available in 580nm 3000K, 4000K and 5000K standard CCT ■ Type 1, 2, 3, 4, 5, R, L standard distributions ■ 0-10V dimming drivers standard ■ IP66 certified Configuration EPA 1SA 1 Arm Side Mt.0.70 2SB 2 Arm Side Mt.1.40 2SL 2 Arm Side Mt.1.20 3ST 3 Arm Side Mt.1.90 3SY*3 Arm Side Mt.1.90 4SC 4 Arm Side Mt.2.50 1W Single Wall Mt.n/a HSF Horz. Slipfitter n/a * Available round poles only. EPA is for Fixture only Distribution SAR1 Type I SAR2 Type II SAR3 Type III SAR4 Type IV SAR5 Type V SARR Type R, Right SARL Type L, Left Drive Current P35 350mA PicoPrism P70 700mA PicoPrism Fixture NFO Option NFO Neighbor Friendly Optic* Fuse Options SF 120, 277, 347 Line Volts DF 208, 240, 480 Line Volts Electrical Module Source 40L 40 LEDs 46W for 350mA 93W for 700mA Color Temperature2 2K 580nm3 3K 3000K 4K 4000K 5K 5000K Controls Photocell Options A25-7 7-pin Photocell Receptacle A30 120V Button Photocell A31 208V Button Photocell A32 240V Button Photocell A33 277V Button Photocell A34 480V Button Photocell A35 347V Button Photocell Approx. Weight = 30 lbs. EPA .070 for 1SA. See configuration for Additional EPAs. *Photometry available for Type III/IV. All others, consult factory. 5"(127 mm) 171/8"(435 mm) 6"(152 mm) FRONT 12"(305.mm) 171/8"(435 mm) BOTTOM Arm cross-section 13/4"(45 mm) 41/4"(108 mm) TOP Mounting Options Side Arm Mount 3 3" O.D. Pole 3.5 3.5" O.D. Pole 4 4" O.D. Pole 5 5" O.D. Pole 6 6" O.D. Pole SQ Square Pole 3000K and warmer CCTs only VSF Vertical Slipfitter Mount for 2" pipe tenon, (2-3/8" O.D.) SVSF Vertical Slipfitter Mount square for 2" pipe tenon, (2-3/8" O.D.) Motion SCL-R Round Pole Mounted Occupancy Sensor up to 16' SCL-S Square Pole Mounted Occupancy Sensor up to 16' SCH-R Round Pole Mounted Occupancy Sensor 16' to 30' SCH-S Square Pole Mounted Occupancy Sensor 16' to 30' Wireless WIR-RMI-IO 120-480V, 1000’ range, wiSCAPE RF control system with on/off/dim, alerts, monitoring and metering capabilities Voltages 120 120V 208 208V 240 240V 277 277V 347 347V4 480 480V4 Fixture Finish BL Black DB Dark Bronze GT Graphite LG Light Gray PS Platinum Silver TT Titanium WH White CC Custom Color* *Consult Representative 1 2 3 4 5 6 7 US Patent No. D674,965 S. Other patents pending.For custom optics and color temperature configurations, contact factory. Turtle friendly. Maximum 500mA drive current for 2K Amber option.347V & 480V currents may be supplied with step-down transformer.350mA only.Not available with other sensor or wireless control options.Specify group and zone at time of order. See www.hubbelllighting.com/sitesync for more details. Order at least one SiteSync interface accessory SWUSB or SWTAB. Each option contains SiteSync License, GUI, and Bridge Node. For Pole Spec Select: http://www.kimlighting.com/products/arms_and_poles/ For Control Spec Select: http://trpssl.com/index.html Microsoft, Encarta, MSN, and Windows are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. SW7PR6,7 Site Sync with 7 pin PCR SWUSB†SiteSync Software on USB SWTAB†SiteSync Windows® Tablet SWBRG†SiteSync Wireless Bridge Node WIR-RME-L wiSCAPE 7-pin Module NXOFM-1R1D-UNV NX 7-pin Module Control Accessories † When ordering with SiteSync, one of the following interface options must be chosen and ordered separately. Each option contains the SiteSync License, GUI and Bridge Node. | 2 | SAR The Archetype® Small PicoPrism LED kl_sarpled_spec.pdf Kim Lighting reserves the right to change specifications without notice. © 2017 KIM LIGHTING | 17760 Rowland Street | City of Industry | CA 91748 P 626.968.5666 | F 626.369.2695 | www.kimlighting.com | Rev. Apr 23, 2019 Lumen Data Absolute Lumens for 350mA Temperature Type I Type II Type III Type III NFO Type IV Type IV NFO Type V Type L/R 3000K 5228 5085 5070 4524 5200 4723 5218 5104 4000K 5362 5215 5200 4640 5333 4844 5352 5234 5000K 5423 5275 5259 4693 5394 4899 5413 5294 Absolute Lumens for 700mA Temperature Type I Type II Type III Type III NFO Type IV Type IV NFO Type V Type L/R 3000K 8716 8670 8640 7664 8705 7945 8957 8554 4000K 8940 8892 8862 7860 8928 8148 9187 8773 5000K 9042 8994 8963 7950 9030 8241 9292 8874 B.U.G. Rating for 350mA (TM15) in Lumens where B = Backlight, U = Uplight, G = Glare Temperature Type I Type II Type III Type III NFO Type IV Type IV NFO Type V Type L/R 3000K B3 U0 G3 B2 U0 G2 B2 U0 G2 B1 U0 G2 B0 U0 G2 B0 U0 G2 B3 U0 G3 B2 U0 G2 4000K B3 U0 G3 B2 U0 G2 B2 U0 G2 B1 U0 G2 B0 U0 G2 B0 U0 G2 B3 U0 G3 B2 U0 G2 5000K B3 U0 G3 B2 U0 G2 B2 U0 G2 B1 U0 G2 B0 U0 G2 B0 U0 G2 B3 U0 G3 B2 U0 G2 B.U.G. Rating for 700mA (TM15) in Lumens where B = Backlight, U = Uplight, G = Glare Temperature Type I Type II Type III Type III NFO Type IV Type IV NFO Type V Type L/R 3000K B3 U0 G3 B3 U0 G3 B2 U0 G2 B2 U0 G2 B1 U0 G3 B0 U0 G2 B3 U0 G3 B3 U0 G3 4000K B3 U0 G3 B3 U0 G3 B2 U0 G2 B2 U0 G2 B1 U0 G3 B0 U0 G3 B3 U0 G3 B3 U0 G3 5000K B3 U0 G3 B3 U0 G3 B2 U0 G2 B2 U0 G2 B1 U0 G3 B0 U0 G3 B3 U0 G3 B3 U0 G3 Electrical Drive Current 350mA 700mA Volts - AC Amps - AC System Watts Volts - AC Amps - AC System Watts 120 0.38 46 120 0.78 93 208 0.22 46 208 0.45 93 240 0.19 46 240 0.39 93 277 0.17 46 277 0.34 93 347 0.13 46 347 0.27 93 480 0.10 46 480 0.19 93 LED performance and lumen output continues to improve at a rapid pace. Log onto www.kimlighting.com to download the most current photometric files from Kim Lighting’s IES File Library. For custom optics and color temperature configurations, contact factory. Spectroradiometric 3000K Average 4000K Average 5000K Average Color Rendering Index (CRI)≥75 ≥70 ≥65 Power Factor >.90 >.90 >.90 Projected Lumen Maintenance* mA 50,000 hrs 100,000 hrs 350 mA 96.67%94.48% 700 mA 92.51%87.87% *Still awaiting independent third party verification | 3 | SAR The Archetype® Small PicoPrism LED kl_sarpled_spec.pdf Kim Lighting reserves the right to change specifications without notice. © 2017 KIM LIGHTING | 17760 Rowland Street | City of Industry | CA 91748 P 626.968.5666 | F 626.369.2695 | www.kimlighting.com | Rev. Apr 23, 2019 Housing: ■Extruded low copper aluminum main body. ■Die-cast low copper aluminum electrical gear compartment. ■Stainless steel hardware. ■ Die cast wall separates the optical and electrical compartment acting as thermal barrier. ■Electrical gear compartment doors are fastened with two hinges and a latch made of stainless steel. ■ Silicone gaskets seal the compartments at the barrier surface. Optical Module: ■ PicoPrism® refractors (enclosed LED PCBs for IP66 rating) aimed toward the task and spreads horizontally to produce great uniformity. ■ Type I, II, III, IV, V, L (left), and R (right) standard distributions. Custom available. ■ 3000K, 4000K, 5000K standard CCT. Amber and custom available. ■ IP66 certified. ■ Die-cast, low copper aluminum heat sink modules provide thermal transfer at PCB level. ■ Anodized aluminum carrier plate and heat sink modules. Lens Frame: ■One-piece low copper aluminum alloy die-cast is secured to housing with two toolless latches. Neighbor Friendly Optic ■ Optional integrated Neighbor Friendly Optic on each LED module to completely control unwanted backlight. Most effective with Type III and IV distibutions. Electrical Characteristics: ■Pre-assembled, aluminum gear tray. ■120V through 480V @ 50/60Hz. ■Class 2, 350mA or 700mA ■Power Factor = >.90 ■National Electrical Code, ANSI/NFPA 70. ■10kV surge suppression. ■ Thermal shield thermal control. ■ -30c starting driver. ■ 0-10V dimming interface. ■ All electronic components are IP66 rated. ■Electronic components are UL and/or CSA recognized. ■ Standard programmable driver for variable drive current settings from 350mA to 700mA. Dimming: ■ 10% to 100% dimming by the use of standard 0-10V interface driver. ■To activate the dimming system, a wiring harness is supplied and attached to the DIM Port (DIM IN) on the thermal shield protection system. This port allows the 0-10V Interface to bypass the thermal shield and control the driver. ■ The thermal shield works in conjunction with the control system to assure that overheating will not harm the LEDs. ■The wiring harness is connected with the use of the Purple lead as the positive (+) and the Grey lead as the negative (-) to an available control signal (by others). Support Arm: ■ Speed Mount and a reinforcing plate are provided with wire strain relief. ■ Speed Mount is square or circular cut for specified pole size and shape. ■Die-cast, low copper aluminum support arm for direct pole mount. ■Die-cast aluminum tool-less entry splice access cover. ■ Terminal block is mounted in the arm cavity and accepts #14 to #8 wire sizes. ■ Prewired to electrical module with quick-disconnect plugs located inside the electrical compartment. ■Optional cast, low copper aluminum horizontal slip-fitter with adaptor plate to secure the luminaire to 1-1/4” to 2” IPS pipe size arms. ■ Optional cast aluminum wall mount plate assembly. Attaches to the wall over the junction box. Luminaire attaches to the wall plate with a square cut Speed Mount. Finish: ■ Fade and abrasion resistant, electrostatically applied, thermally cured, triglycidal isocyanurate (TGIC) polyester powdercoat. ■Standard colors include (BL) Black, (DB) Dark Bronze, (GT) Graphite, (WH) White, (PS) Platinum Silver, (LG) Light Gray, (TT) Titanium, and (CC) Custom Color (Include RAL#). Fusing: SF for 120, 277 and 347 Line Volts DF for 208, 240 and 480 Line Volts. ■High temperature fuse holders factory installed inside the fixture housing. Fuse is included. Certifications and Listings: ■ UL 1598 Standard for wet locations for Luminaires. ■ UL 8750 Standard for Safety for Light Emitting Diode (LED) Equipment for use in Lighting Products. ■IP66 certified. ■ CSA C22.2#250.0 Luminaires. ■ ANSI C136.31-2010 3G Vibration tested and compliant. ■ IDA compliant. ■RoHS compliant. ■Meets Buy American provisions within ARRA. ■IDA approved, 3000K and warmer CCTs only. CAUTION: ■ Fixtures must be grounded in accordance with national, state and/or local electrical codes, Failure to do so may result in serious personal injury. WARRANTY: ■ For full warranty see http://www. hubbelllighting.com/resources/warranty SPECIFICATIONS FixtureHousing 30 mA Max Gray Dimming Lead (-) Standard Input Black (+) White (-)Green (GND) Purple Dimming Lead (+) | 4 | SAR The Archetype® Small PicoPrism LED kl_sarpled_spec.pdf Kim Lighting reserves the right to change specifications without notice. © 2017 KIM LIGHTING | 17760 Rowland Street | City of Industry | CA 91748 P 626.968.5666 | F 626.369.2695 | www.kimlighting.com | Rev. Apr 23, 2019 Kim Lighting reserves the right to change specifications without notice. CONTROLS Gray Wire0-10V Dimming Purple Wire0-10V Dimming Orange Wire10V CustomerDefinedRed WireLine Voltage Brown Wire10V CustomerDefined Black WireLine Voltage White WireNeutral Photocell Receptacle A25-7 Fully gasketed and wired 7-pin receptacle option. Easy access location above the electrical compartment. 7-pin construction allows for a user-defined interface and provides a controlled definition of operational performance. ANSI twist-lock control module by-others. Standard customer operation modes: 1. Traditional on/off photoelectric control. 2. 5-pin wireless photoelectric control for added dimming feature. 3. 7-pin wireless photoelectric control for dimming and additional I/O connections for customer use. Button Photocell A30 for 120V, A31 for 208V, A32 for 240V, A33 for 277V, A35 for 347V, A34 for 480V, Photocell is factory installed inside the housing with a fully gasketed sensor on the side wall. For multiple fixture mountings, one fixture is supplied with a photocell to operate the others. Wireless Controls wiSCAPE™ Hubbell Control Solution’s wiSCAPE™ wireless control modules allow an individual fixture to managed, monitored and measured. The modules communicate securely over a robust certified meshed radio signal. The wiSCAPE modules provide on/off/dim control, external device input, alerts and metering. WIR-RMI-IO wiSCAPE Internal Module, 120-480V, 1000ft range (LOS), 3 Digital Inputs/1 Analog Input, 2 Outputs. WIR-RME-L wiSCAPE External Module,120-480V, 1000ft range (LOS), Internal Photocell, 1 Digital Input, Compatible with the A-25-7H option SiteSync™1 SiteSync™ wireless control system for reduction in energy and maintenance cost while optimizing light quality 24/7. See ordering information or visit www.hubbelllighting.com/products/sitesync for more details. Pole Mounted Round Pole-Mounted Occupancy Sensor up to 16' SCL-R Round Pole-Mounted Occupancy Sensor up to 16’ - an outdoor occupancy sensor with 0-10V interface dimming control that mounts directly to the pole. Wide 360° pattern. Module colors are available in Black, Gray, and White. Module is cut for round pole mounting. Pole diameter is needed upon order. Poles to be drilled in the field will be provided with installation instructions. Ordering Example: SCL-R44/2772/BL3 Square Pole-Mounted Occupancy Sensor up to 16' SCL-S Square Pole-Mounted Occupancy Sensor up to 16’ - an outdoor occupancy sensor with 0-10V interface dimming control that mounts directly to the pole. Wide 360° pattern. Module colors are available in Black, Gray, and White. Module is cut for square pole mounting. Pole diameter is needed upon order. Poles to be drilled in the field will be provided with installation instructions. Ordering Example: SCL-L/2772/BL3 Round Pole-Mounted Occupancy Sensor 16’ to 30’ SCH-R Round Pole-Mounted Occupancy Sensor: 16' to 30’ - an outdoor occupancy sensor with 0-10V interface dimming control that mounts directly to the pole. Wide 360° pattern. Module colors are available in Black, Gray, and White. Module is cut for round pole mounting. Pole diameter is needed upon order. Poles to be drilled in the field will be provided with installation instructions. Ordering Example: SCH-R44/2772/BL3 Square Pole-Mounted Occupancy Sensor 16’ to 30’ SCH-S Square Pole-Mounted Occupancy Sensor: 16 to 30’ - an outdoor occupancy sensor with 0-10V interface dimming control that mounts directly to the pole. Wide 360° pattern. Module colors are available in Black, Gray, and White. Module is cut for round pole mounting. Pole diameter is needed upon order. Poles to be drilled in the field will be provided with installation instructions. Ordering Example: SCH-S/2772/BL3 SCP The SCP is a photo-control with motion sensing accessory thats mounts to the side of any new or existing 3”-5” round or square straight pole. The SCP enables any pole mounted luminaire in excess of 75 watts, to meet California Title 24 requirements with integral 20KV/10KA surge protection for added reliability and serviceability. For more detail: http://www.aal.net/products/sensor_control_ programmable 2Voltage, 3Color, 4Pole Diameter 1 PRECOMMISSIONED SITESYNC ORDERING INFORMATION: When ordering a fixture with the SiteSync lighting control option, additional information will be required to complete the order. The SiteSync Commissioning Form or alternate schedule information must be completed. This form includes Project location, Group information, and Operating schedules. For more detailed information please visit www.HubbellLighting.com/products/sitesync or contact Hubbell Lighting tech support at (800) 345-4928. SiteSync fixtures with occupancy sensor (SWPM) require the mounting height of the fixture for selection of the lens. Examples: SiteSync only : ALT3/P70/60L/3KUV/PS/US/SWP SiteSync with Motion Control: ALT3/P70/60L/3KUV/PS/US/SWPM-20F MOB ORDERING INFORMATION: When ordering a fixture with a dimming occupancy sensor option (MOB), please specify the appropriate information. These settings are specified in the ordering as shown in the example below. ALT3/P70/60L/3KUV/PS/US/MOB - 1 to 30 min - 33%or 50% - ?? / DBT High to Dim Delay Low Level Mounting Height (ft.) 2Voltage, 3Color, 4Pole Diameter 1 PRECOMMISSIONED SITESYNC ORDERING INFORMATION: When ordering a fixture with the SiteSync lighting control option, additional information will be required to complete the order. The SiteSync Commissioning Form or alternate schedule information must be completed. This form includes Project location, Group information, and Operating schedules. For more detailed information please visit www.HubbellLighting.com/products/sitesync or contact Hubbell Lighting tech support at (800) 345-4928. SiteSync fixtures with occupancy sensor (SWPM) require the mounting height of the fixture for selection of the lens. Examples: SiteSync only : ALT3/P70/60L/3KUV/PS/US/SWP SiteSync with Motion Control: ALT3/P70/60L/3KUV/PS/US/SWPM-20F MOB ORDERING INFORMATION: When ordering a fixture with a dimming occupancy sensor option (MOB), please specify the appropriate information. These settings are specified in the ordering as shown in the example below. ALT3/P70/60L/3KUV/PS/US/MOB - 1 to 30 min - 33%or 50% - ?? / DBT High to Dim Delay Low Level Mounting Height (ft.) | 5 | Kim Lighting reserves the right to change specifications without notice. SAR The Archetype® Small PicoPrism LED kl_sarpled_spec.pdf © 2017 KIM LIGHTING | 17760 Rowland Street | City of Industry | CA 91748 P 626.968.5666 | F 626.369.2695 | www.kimlighting.com | Rev. Apr 23, 2019 Wall Mounting: ■Fixture mounts to 3" or 4" junction boxes by a cast aluminum adapter plate with fixture mounting bolts. NOTE: Junction box in wall must provide adequate fixture support. See NEC sections 370-13, 17 and 410-14, 16. Quick-disconnect plug and wiring are provided to allow field connections prior to fixture mounting. Horizontal Slipfitter Mount: ■ Replaces standard mounting arm with a slipfitter which allows fixture to be mounted to a horizontal pole davit-arm with 2" pipe-size mounting end (2 3/8" O.D.). Cast aluminum slipfitter with set screw for an up or down 5° adjustment lock. Bolts to housing from inside the electrical compartment using mounting holes for the standard support arm. Davit-arm must be field drilled at a set screw location to insure against fixture rotation. Finished to match fixture. Vertical Slipfitter Mount: ■ Allows fixture with standard support arm to be mounted to poles having a 2" pipe-size tenon (2 3/8" O.D. x 4 1/2" min. length). All mount- ing configurations can be used (1SA, 2SB, 2SL, 3ST, 3SY, 4SC). 4" square or round die-cast aluminum with flush cap, secured by four 3/8" stainless steel set point allen screws, finished to match fixture and arm. NOTE: 3SY only available on round slipfitter. Neighbor Friendly Optic ■ Integrated Neighbor Friendly Optic on each PicoEmitter™ module to completely control unwanted backlight. Most effective with Type III and IV distibutions. Tamper-Resistant Latch ■ Standard die-cast latch is provided with a captive 10-32 stainless steel flat socket-head screw to prevent unauthorized opening. NOTE: Required only for vandal protection in locationswhere fixtures can be reached by unauthorized persons. OPTIONS Vertical Slipfitter Mount by Kim Pole with 2" pipe-size tenon (by others) stainless steel set screws Round Square Cat. No. VSF-1SA VSF-2SB VSF-2SL VSF-3ST VSF-3SY VSF-4SC Cat. No. SVSF-1SA SVSF-2SB SVSF-2SL SVSF-3ST SVSF-4SC Mounting Configuration 1SA - single arm mount 2SB - 2 at 180° 2SL - 2 at 90° 3ST - 2 at 90° 3SY - 2 at 120° 4SC - 2 at 90° Davit-arm with 2" pipe-size fixture mount (by others) Horizontal Slipfitter Mount by Kim 11/16" 43/4" J-box Wall mount using adapter plate 3" or 4" J-box in wall (by others) | 1 | JOB NOTES TYPE APPROVALS SAR The Archetype® Small PicoPrism LED kl_sarpled_spec.pdf Kim Lighting reserves the right to change specifications without notice. © 2017 KIM LIGHTING | 17760 Rowland Street | City of Industry | CA 91748 P 626.968.5666 | F 626.369.2695 | www.kimlighting.com | Rev. Apr 23, 2019 SPECIFICATIONS ORDERING CODE FEATURES Certifications ■ PicoPrism® technology1 ■ Full uplight cutoff ■ Available in 580nm 3000K, 4000K and 5000K standard CCT ■ Type 1, 2, 3, 4, 5, R, L standard distributions ■ 0-10V dimming drivers standard ■ IP66 certified Configuration EPA 1SA 1 Arm Side Mt.0.70 2SB 2 Arm Side Mt.1.40 2SL 2 Arm Side Mt.1.20 3ST 3 Arm Side Mt.1.90 3SY*3 Arm Side Mt.1.90 4SC 4 Arm Side Mt.2.50 1W Single Wall Mt.n/a HSF Horz. Slipfitter n/a * Available round poles only. EPA is for Fixture only Distribution SAR1 Type I SAR2 Type II SAR3 Type III SAR4 Type IV SAR5 Type V SARR Type R, Right SARL Type L, Left Drive Current P35 350mA PicoPrism P70 700mA PicoPrism Fixture NFO Option NFO Neighbor Friendly Optic* Fuse Options SF 120, 277, 347 Line Volts DF 208, 240, 480 Line Volts Electrical Module Source 40L 40 LEDs 46W for 350mA 93W for 700mA Color Temperature2 2K 580nm3 3K 3000K 4K 4000K 5K 5000K Controls Photocell Options A25-7 7-pin Photocell Receptacle A30 120V Button Photocell A31 208V Button Photocell A32 240V Button Photocell A33 277V Button Photocell A34 480V Button Photocell A35 347V Button Photocell Approx. Weight = 30 lbs. EPA .070 for 1SA. See configuration for Additional EPAs. *Photometry available for Type III/IV. All others, consult factory. 5"(127 mm) 171/8"(435 mm) 6"(152 mm) FRONT 12"(305.mm) 171/8"(435 mm) BOTTOM Arm cross-section 13/4"(45 mm) 41/4"(108 mm) TOP Mounting Options Side Arm Mount 3 3" O.D. Pole 3.5 3.5" O.D. Pole 4 4" O.D. Pole 5 5" O.D. Pole 6 6" O.D. Pole SQ Square Pole 3000K and warmer CCTs only VSF Vertical Slipfitter Mount for 2" pipe tenon, (2-3/8" O.D.) SVSF Vertical Slipfitter Mount square for 2" pipe tenon, (2-3/8" O.D.) Motion SCL-R Round Pole Mounted Occupancy Sensor up to 16' SCL-S Square Pole Mounted Occupancy Sensor up to 16' SCH-R Round Pole Mounted Occupancy Sensor 16' to 30' SCH-S Square Pole Mounted Occupancy Sensor 16' to 30' Wireless WIR-RMI-IO 120-480V, 1000’ range, wiSCAPE RF control system with on/off/dim, alerts, monitoring and metering capabilities Voltages 120 120V 208 208V 240 240V 277 277V 347 347V4 480 480V4 Fixture Finish BL Black DB Dark Bronze GT Graphite LG Light Gray PS Platinum Silver TT Titanium WH White CC Custom Color* *Consult Representative 1 2 3 4 5 6 7 US Patent No. D674,965 S. Other patents pending.For custom optics and color temperature configurations, contact factory. Turtle friendly. Maximum 500mA drive current for 2K Amber option.347V & 480V currents may be supplied with step-down transformer.350mA only.Not available with other sensor or wireless control options.Specify group and zone at time of order. See www.hubbelllighting.com/sitesync for more details. Order at least one SiteSync interface accessory SWUSB or SWTAB. Each option contains SiteSync License, GUI, and Bridge Node. For Pole Spec Select: http://www.kimlighting.com/products/arms_and_poles/ For Control Spec Select: http://trpssl.com/index.html Microsoft, Encarta, MSN, and Windows are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. SW7PR6,7 Site Sync with 7 pin PCR SWUSB†SiteSync Software on USB SWTAB†SiteSync Windows® Tablet SWBRG†SiteSync Wireless Bridge Node WIR-RME-L wiSCAPE 7-pin Module NXOFM-1R1D-UNV NX 7-pin Module Control Accessories † When ordering with SiteSync, one of the following interface options must be chosen and ordered separately. Each option contains the SiteSync License, GUI and Bridge Node. | 2 | SAR The Archetype® Small PicoPrism LED kl_sarpled_spec.pdf Kim Lighting reserves the right to change specifications without notice. © 2017 KIM LIGHTING | 17760 Rowland Street | City of Industry | CA 91748 P 626.968.5666 | F 626.369.2695 | www.kimlighting.com | Rev. Apr 23, 2019 Lumen Data Absolute Lumens for 350mA Temperature Type I Type II Type III Type III NFO Type IV Type IV NFO Type V Type L/R 3000K 5228 5085 5070 4524 5200 4723 5218 5104 4000K 5362 5215 5200 4640 5333 4844 5352 5234 5000K 5423 5275 5259 4693 5394 4899 5413 5294 Absolute Lumens for 700mA Temperature Type I Type II Type III Type III NFO Type IV Type IV NFO Type V Type L/R 3000K 8716 8670 8640 7664 8705 7945 8957 8554 4000K 8940 8892 8862 7860 8928 8148 9187 8773 5000K 9042 8994 8963 7950 9030 8241 9292 8874 B.U.G. Rating for 350mA (TM15) in Lumens where B = Backlight, U = Uplight, G = Glare Temperature Type I Type II Type III Type III NFO Type IV Type IV NFO Type V Type L/R 3000K B3 U0 G3 B2 U0 G2 B2 U0 G2 B1 U0 G2 B0 U0 G2 B0 U0 G2 B3 U0 G3 B2 U0 G2 4000K B3 U0 G3 B2 U0 G2 B2 U0 G2 B1 U0 G2 B0 U0 G2 B0 U0 G2 B3 U0 G3 B2 U0 G2 5000K B3 U0 G3 B2 U0 G2 B2 U0 G2 B1 U0 G2 B0 U0 G2 B0 U0 G2 B3 U0 G3 B2 U0 G2 B.U.G. Rating for 700mA (TM15) in Lumens where B = Backlight, U = Uplight, G = Glare Temperature Type I Type II Type III Type III NFO Type IV Type IV NFO Type V Type L/R 3000K B3 U0 G3 B3 U0 G3 B2 U0 G2 B2 U0 G2 B1 U0 G3 B0 U0 G2 B3 U0 G3 B3 U0 G3 4000K B3 U0 G3 B3 U0 G3 B2 U0 G2 B2 U0 G2 B1 U0 G3 B0 U0 G3 B3 U0 G3 B3 U0 G3 5000K B3 U0 G3 B3 U0 G3 B2 U0 G2 B2 U0 G2 B1 U0 G3 B0 U0 G3 B3 U0 G3 B3 U0 G3 Electrical Drive Current 350mA 700mA Volts - AC Amps - AC System Watts Volts - AC Amps - AC System Watts 120 0.38 46 120 0.78 93 208 0.22 46 208 0.45 93 240 0.19 46 240 0.39 93 277 0.17 46 277 0.34 93 347 0.13 46 347 0.27 93 480 0.10 46 480 0.19 93 LED performance and lumen output continues to improve at a rapid pace. Log onto www.kimlighting.com to download the most current photometric files from Kim Lighting’s IES File Library. For custom optics and color temperature configurations, contact factory. Spectroradiometric 3000K Average 4000K Average 5000K Average Color Rendering Index (CRI)≥75 ≥70 ≥65 Power Factor >.90 >.90 >.90 Projected Lumen Maintenance* mA 50,000 hrs 100,000 hrs 350 mA 96.67%94.48% 700 mA 92.51%87.87% *Still awaiting independent third party verification | 3 | SAR The Archetype® Small PicoPrism LED kl_sarpled_spec.pdf Kim Lighting reserves the right to change specifications without notice. © 2017 KIM LIGHTING | 17760 Rowland Street | City of Industry | CA 91748 P 626.968.5666 | F 626.369.2695 | www.kimlighting.com | Rev. Apr 23, 2019 Housing: ■Extruded low copper aluminum main body. ■Die-cast low copper aluminum electrical gear compartment. ■Stainless steel hardware. ■ Die cast wall separates the optical and electrical compartment acting as thermal barrier. ■Electrical gear compartment doors are fastened with two hinges and a latch made of stainless steel. ■ Silicone gaskets seal the compartments at the barrier surface. Optical Module: ■ PicoPrism® refractors (enclosed LED PCBs for IP66 rating) aimed toward the task and spreads horizontally to produce great uniformity. ■ Type I, II, III, IV, V, L (left), and R (right) standard distributions. Custom available. ■ 3000K, 4000K, 5000K standard CCT. Amber and custom available. ■ IP66 certified. ■ Die-cast, low copper aluminum heat sink modules provide thermal transfer at PCB level. ■ Anodized aluminum carrier plate and heat sink modules. Lens Frame: ■One-piece low copper aluminum alloy die-cast is secured to housing with two toolless latches. Neighbor Friendly Optic ■ Optional integrated Neighbor Friendly Optic on each LED module to completely control unwanted backlight. Most effective with Type III and IV distibutions. Electrical Characteristics: ■Pre-assembled, aluminum gear tray. ■120V through 480V @ 50/60Hz. ■Class 2, 350mA or 700mA ■Power Factor = >.90 ■National Electrical Code, ANSI/NFPA 70. ■10kV surge suppression. ■ Thermal shield thermal control. ■ -30c starting driver. ■ 0-10V dimming interface. ■ All electronic components are IP66 rated. ■Electronic components are UL and/or CSA recognized. ■ Standard programmable driver for variable drive current settings from 350mA to 700mA. Dimming: ■ 10% to 100% dimming by the use of standard 0-10V interface driver. ■To activate the dimming system, a wiring harness is supplied and attached to the DIM Port (DIM IN) on the thermal shield protection system. This port allows the 0-10V Interface to bypass the thermal shield and control the driver. ■ The thermal shield works in conjunction with the control system to assure that overheating will not harm the LEDs. ■The wiring harness is connected with the use of the Purple lead as the positive (+) and the Grey lead as the negative (-) to an available control signal (by others). Support Arm: ■ Speed Mount and a reinforcing plate are provided with wire strain relief. ■ Speed Mount is square or circular cut for specified pole size and shape. ■Die-cast, low copper aluminum support arm for direct pole mount. ■Die-cast aluminum tool-less entry splice access cover. ■ Terminal block is mounted in the arm cavity and accepts #14 to #8 wire sizes. ■ Prewired to electrical module with quick-disconnect plugs located inside the electrical compartment. ■Optional cast, low copper aluminum horizontal slip-fitter with adaptor plate to secure the luminaire to 1-1/4” to 2” IPS pipe size arms. ■ Optional cast aluminum wall mount plate assembly. Attaches to the wall over the junction box. Luminaire attaches to the wall plate with a square cut Speed Mount. Finish: ■ Fade and abrasion resistant, electrostatically applied, thermally cured, triglycidal isocyanurate (TGIC) polyester powdercoat. ■Standard colors include (BL) Black, (DB) Dark Bronze, (GT) Graphite, (WH) White, (PS) Platinum Silver, (LG) Light Gray, (TT) Titanium, and (CC) Custom Color (Include RAL#). Fusing: SF for 120, 277 and 347 Line Volts DF for 208, 240 and 480 Line Volts. ■High temperature fuse holders factory installed inside the fixture housing. Fuse is included. Certifications and Listings: ■ UL 1598 Standard for wet locations for Luminaires. ■ UL 8750 Standard for Safety for Light Emitting Diode (LED) Equipment for use in Lighting Products. ■IP66 certified. ■ CSA C22.2#250.0 Luminaires. ■ ANSI C136.31-2010 3G Vibration tested and compliant. ■ IDA compliant. ■RoHS compliant. ■Meets Buy American provisions within ARRA. ■IDA approved, 3000K and warmer CCTs only. CAUTION: ■ Fixtures must be grounded in accordance with national, state and/or local electrical codes, Failure to do so may result in serious personal injury. WARRANTY: ■ For full warranty see http://www. hubbelllighting.com/resources/warranty SPECIFICATIONS FixtureHousing 30 mA Max Gray Dimming Lead (-) Standard Input Black (+) White (-)Green (GND) Purple Dimming Lead (+) | 4 | SAR The Archetype® Small PicoPrism LED kl_sarpled_spec.pdf Kim Lighting reserves the right to change specifications without notice. © 2017 KIM LIGHTING | 17760 Rowland Street | City of Industry | CA 91748 P 626.968.5666 | F 626.369.2695 | www.kimlighting.com | Rev. Apr 23, 2019 Kim Lighting reserves the right to change specifications without notice. CONTROLS Gray Wire0-10V Dimming Purple Wire0-10V Dimming Orange Wire10V CustomerDefinedRed WireLine Voltage Brown Wire10V CustomerDefined Black WireLine Voltage White WireNeutral Photocell Receptacle A25-7 Fully gasketed and wired 7-pin receptacle option. Easy access location above the electrical compartment. 7-pin construction allows for a user-defined interface and provides a controlled definition of operational performance. ANSI twist-lock control module by-others. Standard customer operation modes: 1. Traditional on/off photoelectric control. 2. 5-pin wireless photoelectric control for added dimming feature. 3. 7-pin wireless photoelectric control for dimming and additional I/O connections for customer use. Button Photocell A30 for 120V, A31 for 208V, A32 for 240V, A33 for 277V, A35 for 347V, A34 for 480V, Photocell is factory installed inside the housing with a fully gasketed sensor on the side wall. For multiple fixture mountings, one fixture is supplied with a photocell to operate the others. Wireless Controls wiSCAPE™ Hubbell Control Solution’s wiSCAPE™ wireless control modules allow an individual fixture to managed, monitored and measured. The modules communicate securely over a robust certified meshed radio signal. The wiSCAPE modules provide on/off/dim control, external device input, alerts and metering. WIR-RMI-IO wiSCAPE Internal Module, 120-480V, 1000ft range (LOS), 3 Digital Inputs/1 Analog Input, 2 Outputs. WIR-RME-L wiSCAPE External Module,120-480V, 1000ft range (LOS), Internal Photocell, 1 Digital Input, Compatible with the A-25-7H option SiteSync™1 SiteSync™ wireless control system for reduction in energy and maintenance cost while optimizing light quality 24/7. See ordering information or visit www.hubbelllighting.com/products/sitesync for more details. Pole Mounted Round Pole-Mounted Occupancy Sensor up to 16' SCL-R Round Pole-Mounted Occupancy Sensor up to 16’ - an outdoor occupancy sensor with 0-10V interface dimming control that mounts directly to the pole. Wide 360° pattern. Module colors are available in Black, Gray, and White. Module is cut for round pole mounting. Pole diameter is needed upon order. Poles to be drilled in the field will be provided with installation instructions. Ordering Example: SCL-R44/2772/BL3 Square Pole-Mounted Occupancy Sensor up to 16' SCL-S Square Pole-Mounted Occupancy Sensor up to 16’ - an outdoor occupancy sensor with 0-10V interface dimming control that mounts directly to the pole. Wide 360° pattern. Module colors are available in Black, Gray, and White. Module is cut for square pole mounting. Pole diameter is needed upon order. Poles to be drilled in the field will be provided with installation instructions. Ordering Example: SCL-L/2772/BL3 Round Pole-Mounted Occupancy Sensor 16’ to 30’ SCH-R Round Pole-Mounted Occupancy Sensor: 16' to 30’ - an outdoor occupancy sensor with 0-10V interface dimming control that mounts directly to the pole. Wide 360° pattern. Module colors are available in Black, Gray, and White. Module is cut for round pole mounting. Pole diameter is needed upon order. Poles to be drilled in the field will be provided with installation instructions. Ordering Example: SCH-R44/2772/BL3 Square Pole-Mounted Occupancy Sensor 16’ to 30’ SCH-S Square Pole-Mounted Occupancy Sensor: 16 to 30’ - an outdoor occupancy sensor with 0-10V interface dimming control that mounts directly to the pole. Wide 360° pattern. Module colors are available in Black, Gray, and White. Module is cut for round pole mounting. Pole diameter is needed upon order. Poles to be drilled in the field will be provided with installation instructions. Ordering Example: SCH-S/2772/BL3 SCP The SCP is a photo-control with motion sensing accessory thats mounts to the side of any new or existing 3”-5” round or square straight pole. The SCP enables any pole mounted luminaire in excess of 75 watts, to meet California Title 24 requirements with integral 20KV/10KA surge protection for added reliability and serviceability. For more detail: http://www.aal.net/products/sensor_control_ programmable 2Voltage, 3Color, 4Pole Diameter 1 PRECOMMISSIONED SITESYNC ORDERING INFORMATION: When ordering a fixture with the SiteSync lighting control option, additional information will be required to complete the order. The SiteSync Commissioning Form or alternate schedule information must be completed. This form includes Project location, Group information, and Operating schedules. For more detailed information please visit www.HubbellLighting.com/products/sitesync or contact Hubbell Lighting tech support at (800) 345-4928. SiteSync fixtures with occupancy sensor (SWPM) require the mounting height of the fixture for selection of the lens. Examples: SiteSync only : ALT3/P70/60L/3KUV/PS/US/SWP SiteSync with Motion Control: ALT3/P70/60L/3KUV/PS/US/SWPM-20F MOB ORDERING INFORMATION: When ordering a fixture with a dimming occupancy sensor option (MOB), please specify the appropriate information. These settings are specified in the ordering as shown in the example below. ALT3/P70/60L/3KUV/PS/US/MOB - 1 to 30 min - 33%or 50% - ?? / DBT High to Dim Delay Low Level Mounting Height (ft.) 2Voltage, 3Color, 4Pole Diameter 1 PRECOMMISSIONED SITESYNC ORDERING INFORMATION: When ordering a fixture with the SiteSync lighting control option, additional information will be required to complete the order. The SiteSync Commissioning Form or alternate schedule information must be completed. This form includes Project location, Group information, and Operating schedules. For more detailed information please visit www.HubbellLighting.com/products/sitesync or contact Hubbell Lighting tech support at (800) 345-4928. SiteSync fixtures with occupancy sensor (SWPM) require the mounting height of the fixture for selection of the lens. Examples: SiteSync only : ALT3/P70/60L/3KUV/PS/US/SWP SiteSync with Motion Control: ALT3/P70/60L/3KUV/PS/US/SWPM-20F MOB ORDERING INFORMATION: When ordering a fixture with a dimming occupancy sensor option (MOB), please specify the appropriate information. These settings are specified in the ordering as shown in the example below. ALT3/P70/60L/3KUV/PS/US/MOB - 1 to 30 min - 33%or 50% - ?? / DBT High to Dim Delay Low Level Mounting Height (ft.) | 5 | Kim Lighting reserves the right to change specifications without notice. SAR The Archetype® Small PicoPrism LED kl_sarpled_spec.pdf © 2017 KIM LIGHTING | 17760 Rowland Street | City of Industry | CA 91748 P 626.968.5666 | F 626.369.2695 | www.kimlighting.com | Rev. Apr 23, 2019 Wall Mounting: ■Fixture mounts to 3" or 4" junction boxes by a cast aluminum adapter plate with fixture mounting bolts. NOTE: Junction box in wall must provide adequate fixture support. See NEC sections 370-13, 17 and 410-14, 16. Quick-disconnect plug and wiring are provided to allow field connections prior to fixture mounting. Horizontal Slipfitter Mount: ■ Replaces standard mounting arm with a slipfitter which allows fixture to be mounted to a horizontal pole davit-arm with 2" pipe-size mounting end (2 3/8" O.D.). Cast aluminum slipfitter with set screw for an up or down 5° adjustment lock. Bolts to housing from inside the electrical compartment using mounting holes for the standard support arm. Davit-arm must be field drilled at a set screw location to insure against fixture rotation. Finished to match fixture. Vertical Slipfitter Mount: ■ Allows fixture with standard support arm to be mounted to poles having a 2" pipe-size tenon (2 3/8" O.D. x 4 1/2" min. length). All mount- ing configurations can be used (1SA, 2SB, 2SL, 3ST, 3SY, 4SC). 4" square or round die-cast aluminum with flush cap, secured by four 3/8" stainless steel set point allen screws, finished to match fixture and arm. NOTE: 3SY only available on round slipfitter. Neighbor Friendly Optic ■ Integrated Neighbor Friendly Optic on each PicoEmitter™ module to completely control unwanted backlight. Most effective with Type III and IV distibutions. Tamper-Resistant Latch ■ Standard die-cast latch is provided with a captive 10-32 stainless steel flat socket-head screw to prevent unauthorized opening. NOTE: Required only for vandal protection in locationswhere fixtures can be reached by unauthorized persons. OPTIONS Vertical Slipfitter Mount by Kim Pole with 2" pipe-size tenon (by others) stainless steel set screws Round Square Cat. No. VSF-1SA VSF-2SB VSF-2SL VSF-3ST VSF-3SY VSF-4SC Cat. No. SVSF-1SA SVSF-2SB SVSF-2SL SVSF-3ST SVSF-4SC Mounting Configuration 1SA - single arm mount 2SB - 2 at 180° 2SL - 2 at 90° 3ST - 2 at 90° 3SY - 2 at 120° 4SC - 2 at 90° Davit-arm with 2" pipe-size fixture mount (by others) Horizontal Slipfitter Mount by Kim 11/16" 43/4" J-box Wall mount using adapter plate 3" or 4" J-box in wall (by others) | 1 | JOB NOTES TYPE APPROVALS SAR The Archetype® Small PicoPrism LED kl_sarpled_spec.pdf Kim Lighting reserves the right to change specifications without notice. © 2017 KIM LIGHTING | 17760 Rowland Street | City of Industry | CA 91748 P 626.968.5666 | F 626.369.2695 | www.kimlighting.com | Rev. Apr 23, 2019 SPECIFICATIONS ORDERING CODE FEATURES Certifications ■ PicoPrism® technology1 ■ Full uplight cutoff ■ Available in 580nm 3000K, 4000K and 5000K standard CCT ■ Type 1, 2, 3, 4, 5, R, L standard distributions ■ 0-10V dimming drivers standard ■ IP66 certified Configuration EPA 1SA 1 Arm Side Mt.0.70 2SB 2 Arm Side Mt.1.40 2SL 2 Arm Side Mt.1.20 3ST 3 Arm Side Mt.1.90 3SY*3 Arm Side Mt.1.90 4SC 4 Arm Side Mt.2.50 1W Single Wall Mt.n/a HSF Horz. Slipfitter n/a * Available round poles only. EPA is for Fixture only Distribution SAR1 Type I SAR2 Type II SAR3 Type III SAR4 Type IV SAR5 Type V SARR Type R, Right SARL Type L, Left Drive Current P35 350mA PicoPrism P70 700mA PicoPrism Fixture NFO Option NFO Neighbor Friendly Optic* Fuse Options SF 120, 277, 347 Line Volts DF 208, 240, 480 Line Volts Electrical Module Source 40L 40 LEDs 46W for 350mA 93W for 700mA Color Temperature2 2K 580nm3 3K 3000K 4K 4000K 5K 5000K Controls Photocell Options A25-7 7-pin Photocell Receptacle A30 120V Button Photocell A31 208V Button Photocell A32 240V Button Photocell A33 277V Button Photocell A34 480V Button Photocell A35 347V Button Photocell Approx. Weight = 30 lbs. EPA .070 for 1SA. See configuration for Additional EPAs. *Photometry available for Type III/IV. All others, consult factory. 5"(127 mm) 171/8"(435 mm) 6"(152 mm) FRONT 12"(305.mm) 171/8"(435 mm) BOTTOM Arm cross-section 13/4"(45 mm) 41/4"(108 mm) TOP Mounting Options Side Arm Mount 3 3" O.D. Pole 3.5 3.5" O.D. Pole 4 4" O.D. Pole 5 5" O.D. Pole 6 6" O.D. Pole SQ Square Pole 3000K and warmer CCTs only VSF Vertical Slipfitter Mount for 2" pipe tenon, (2-3/8" O.D.) SVSF Vertical Slipfitter Mount square for 2" pipe tenon, (2-3/8" O.D.) Motion SCL-R Round Pole Mounted Occupancy Sensor up to 16' SCL-S Square Pole Mounted Occupancy Sensor up to 16' SCH-R Round Pole Mounted Occupancy Sensor 16' to 30' SCH-S Square Pole Mounted Occupancy Sensor 16' to 30' Wireless WIR-RMI-IO 120-480V, 1000’ range, wiSCAPE RF control system with on/off/dim, alerts, monitoring and metering capabilities Voltages 120 120V 208 208V 240 240V 277 277V 347 347V4 480 480V4 Fixture Finish BL Black DB Dark Bronze GT Graphite LG Light Gray PS Platinum Silver TT Titanium WH White CC Custom Color* *Consult Representative 1 2 3 4 5 6 7 US Patent No. D674,965 S. Other patents pending.For custom optics and color temperature configurations, contact factory. Turtle friendly. Maximum 500mA drive current for 2K Amber option.347V & 480V currents may be supplied with step-down transformer.350mA only.Not available with other sensor or wireless control options.Specify group and zone at time of order. See www.hubbelllighting.com/sitesync for more details. Order at least one SiteSync interface accessory SWUSB or SWTAB. Each option contains SiteSync License, GUI, and Bridge Node. For Pole Spec Select: http://www.kimlighting.com/products/arms_and_poles/ For Control Spec Select: http://trpssl.com/index.html Microsoft, Encarta, MSN, and Windows are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. SW7PR6,7 Site Sync with 7 pin PCR SWUSB†SiteSync Software on USB SWTAB†SiteSync Windows® Tablet SWBRG†SiteSync Wireless Bridge Node WIR-RME-L wiSCAPE 7-pin Module NXOFM-1R1D-UNV NX 7-pin Module Control Accessories † When ordering with SiteSync, one of the following interface options must be chosen and ordered separately. Each option contains the SiteSync License, GUI and Bridge Node. | 2 | SAR The Archetype® Small PicoPrism LED kl_sarpled_spec.pdf Kim Lighting reserves the right to change specifications without notice. © 2017 KIM LIGHTING | 17760 Rowland Street | City of Industry | CA 91748 P 626.968.5666 | F 626.369.2695 | www.kimlighting.com | Rev. Apr 23, 2019 Lumen Data Absolute Lumens for 350mA Temperature Type I Type II Type III Type III NFO Type IV Type IV NFO Type V Type L/R 3000K 5228 5085 5070 4524 5200 4723 5218 5104 4000K 5362 5215 5200 4640 5333 4844 5352 5234 5000K 5423 5275 5259 4693 5394 4899 5413 5294 Absolute Lumens for 700mA Temperature Type I Type II Type III Type III NFO Type IV Type IV NFO Type V Type L/R 3000K 8716 8670 8640 7664 8705 7945 8957 8554 4000K 8940 8892 8862 7860 8928 8148 9187 8773 5000K 9042 8994 8963 7950 9030 8241 9292 8874 B.U.G. Rating for 350mA (TM15) in Lumens where B = Backlight, U = Uplight, G = Glare Temperature Type I Type II Type III Type III NFO Type IV Type IV NFO Type V Type L/R 3000K B3 U0 G3 B2 U0 G2 B2 U0 G2 B1 U0 G2 B0 U0 G2 B0 U0 G2 B3 U0 G3 B2 U0 G2 4000K B3 U0 G3 B2 U0 G2 B2 U0 G2 B1 U0 G2 B0 U0 G2 B0 U0 G2 B3 U0 G3 B2 U0 G2 5000K B3 U0 G3 B2 U0 G2 B2 U0 G2 B1 U0 G2 B0 U0 G2 B0 U0 G2 B3 U0 G3 B2 U0 G2 B.U.G. Rating for 700mA (TM15) in Lumens where B = Backlight, U = Uplight, G = Glare Temperature Type I Type II Type III Type III NFO Type IV Type IV NFO Type V Type L/R 3000K B3 U0 G3 B3 U0 G3 B2 U0 G2 B2 U0 G2 B1 U0 G3 B0 U0 G2 B3 U0 G3 B3 U0 G3 4000K B3 U0 G3 B3 U0 G3 B2 U0 G2 B2 U0 G2 B1 U0 G3 B0 U0 G3 B3 U0 G3 B3 U0 G3 5000K B3 U0 G3 B3 U0 G3 B2 U0 G2 B2 U0 G2 B1 U0 G3 B0 U0 G3 B3 U0 G3 B3 U0 G3 Electrical Drive Current 350mA 700mA Volts - AC Amps - AC System Watts Volts - AC Amps - AC System Watts 120 0.38 46 120 0.78 93 208 0.22 46 208 0.45 93 240 0.19 46 240 0.39 93 277 0.17 46 277 0.34 93 347 0.13 46 347 0.27 93 480 0.10 46 480 0.19 93 LED performance and lumen output continues to improve at a rapid pace. Log onto www.kimlighting.com to download the most current photometric files from Kim Lighting’s IES File Library. For custom optics and color temperature configurations, contact factory. Spectroradiometric 3000K Average 4000K Average 5000K Average Color Rendering Index (CRI)≥75 ≥70 ≥65 Power Factor >.90 >.90 >.90 Projected Lumen Maintenance* mA 50,000 hrs 100,000 hrs 350 mA 96.67%94.48% 700 mA 92.51%87.87% *Still awaiting independent third party verification | 3 | SAR The Archetype® Small PicoPrism LED kl_sarpled_spec.pdf Kim Lighting reserves the right to change specifications without notice. © 2017 KIM LIGHTING | 17760 Rowland Street | City of Industry | CA 91748 P 626.968.5666 | F 626.369.2695 | www.kimlighting.com | Rev. Apr 23, 2019 Housing: ■Extruded low copper aluminum main body. ■Die-cast low copper aluminum electrical gear compartment. ■Stainless steel hardware. ■ Die cast wall separates the optical and electrical compartment acting as thermal barrier. ■Electrical gear compartment doors are fastened with two hinges and a latch made of stainless steel. ■ Silicone gaskets seal the compartments at the barrier surface. Optical Module: ■ PicoPrism® refractors (enclosed LED PCBs for IP66 rating) aimed toward the task and spreads horizontally to produce great uniformity. ■ Type I, II, III, IV, V, L (left), and R (right) standard distributions. Custom available. ■ 3000K, 4000K, 5000K standard CCT. Amber and custom available. ■ IP66 certified. ■ Die-cast, low copper aluminum heat sink modules provide thermal transfer at PCB level. ■ Anodized aluminum carrier plate and heat sink modules. Lens Frame: ■One-piece low copper aluminum alloy die-cast is secured to housing with two toolless latches. Neighbor Friendly Optic ■ Optional integrated Neighbor Friendly Optic on each LED module to completely control unwanted backlight. Most effective with Type III and IV distibutions. Electrical Characteristics: ■Pre-assembled, aluminum gear tray. ■120V through 480V @ 50/60Hz. ■Class 2, 350mA or 700mA ■Power Factor = >.90 ■National Electrical Code, ANSI/NFPA 70. ■10kV surge suppression. ■ Thermal shield thermal control. ■ -30c starting driver. ■ 0-10V dimming interface. ■ All electronic components are IP66 rated. ■Electronic components are UL and/or CSA recognized. ■ Standard programmable driver for variable drive current settings from 350mA to 700mA. Dimming: ■ 10% to 100% dimming by the use of standard 0-10V interface driver. ■To activate the dimming system, a wiring harness is supplied and attached to the DIM Port (DIM IN) on the thermal shield protection system. This port allows the 0-10V Interface to bypass the thermal shield and control the driver. ■ The thermal shield works in conjunction with the control system to assure that overheating will not harm the LEDs. ■The wiring harness is connected with the use of the Purple lead as the positive (+) and the Grey lead as the negative (-) to an available control signal (by others). Support Arm: ■ Speed Mount and a reinforcing plate are provided with wire strain relief. ■ Speed Mount is square or circular cut for specified pole size and shape. ■Die-cast, low copper aluminum support arm for direct pole mount. ■Die-cast aluminum tool-less entry splice access cover. ■ Terminal block is mounted in the arm cavity and accepts #14 to #8 wire sizes. ■ Prewired to electrical module with quick-disconnect plugs located inside the electrical compartment. ■Optional cast, low copper aluminum horizontal slip-fitter with adaptor plate to secure the luminaire to 1-1/4” to 2” IPS pipe size arms. ■ Optional cast aluminum wall mount plate assembly. Attaches to the wall over the junction box. Luminaire attaches to the wall plate with a square cut Speed Mount. Finish: ■ Fade and abrasion resistant, electrostatically applied, thermally cured, triglycidal isocyanurate (TGIC) polyester powdercoat. ■Standard colors include (BL) Black, (DB) Dark Bronze, (GT) Graphite, (WH) White, (PS) Platinum Silver, (LG) Light Gray, (TT) Titanium, and (CC) Custom Color (Include RAL#). Fusing: SF for 120, 277 and 347 Line Volts DF for 208, 240 and 480 Line Volts. ■High temperature fuse holders factory installed inside the fixture housing. Fuse is included. Certifications and Listings: ■ UL 1598 Standard for wet locations for Luminaires. ■ UL 8750 Standard for Safety for Light Emitting Diode (LED) Equipment for use in Lighting Products. ■IP66 certified. ■ CSA C22.2#250.0 Luminaires. ■ ANSI C136.31-2010 3G Vibration tested and compliant. ■ IDA compliant. ■RoHS compliant. ■Meets Buy American provisions within ARRA. ■IDA approved, 3000K and warmer CCTs only. CAUTION: ■ Fixtures must be grounded in accordance with national, state and/or local electrical codes, Failure to do so may result in serious personal injury. WARRANTY: ■ For full warranty see http://www. hubbelllighting.com/resources/warranty SPECIFICATIONS FixtureHousing 30 mA Max Gray Dimming Lead (-) Standard Input Black (+) White (-)Green (GND) Purple Dimming Lead (+) | 4 | SAR The Archetype® Small PicoPrism LED kl_sarpled_spec.pdf Kim Lighting reserves the right to change specifications without notice. © 2017 KIM LIGHTING | 17760 Rowland Street | City of Industry | CA 91748 P 626.968.5666 | F 626.369.2695 | www.kimlighting.com | Rev. Apr 23, 2019 Kim Lighting reserves the right to change specifications without notice. CONTROLS Gray Wire0-10V Dimming Purple Wire0-10V Dimming Orange Wire10V CustomerDefinedRed WireLine Voltage Brown Wire10V CustomerDefined Black WireLine Voltage White WireNeutral Photocell Receptacle A25-7 Fully gasketed and wired 7-pin receptacle option. Easy access location above the electrical compartment. 7-pin construction allows for a user-defined interface and provides a controlled definition of operational performance. ANSI twist-lock control module by-others. Standard customer operation modes: 1. Traditional on/off photoelectric control. 2. 5-pin wireless photoelectric control for added dimming feature. 3. 7-pin wireless photoelectric control for dimming and additional I/O connections for customer use. Button Photocell A30 for 120V, A31 for 208V, A32 for 240V, A33 for 277V, A35 for 347V, A34 for 480V, Photocell is factory installed inside the housing with a fully gasketed sensor on the side wall. For multiple fixture mountings, one fixture is supplied with a photocell to operate the others. Wireless Controls wiSCAPE™ Hubbell Control Solution’s wiSCAPE™ wireless control modules allow an individual fixture to managed, monitored and measured. The modules communicate securely over a robust certified meshed radio signal. The wiSCAPE modules provide on/off/dim control, external device input, alerts and metering. WIR-RMI-IO wiSCAPE Internal Module, 120-480V, 1000ft range (LOS), 3 Digital Inputs/1 Analog Input, 2 Outputs. WIR-RME-L wiSCAPE External Module,120-480V, 1000ft range (LOS), Internal Photocell, 1 Digital Input, Compatible with the A-25-7H option SiteSync™1 SiteSync™ wireless control system for reduction in energy and maintenance cost while optimizing light quality 24/7. See ordering information or visit www.hubbelllighting.com/products/sitesync for more details. Pole Mounted Round Pole-Mounted Occupancy Sensor up to 16' SCL-R Round Pole-Mounted Occupancy Sensor up to 16’ - an outdoor occupancy sensor with 0-10V interface dimming control that mounts directly to the pole. Wide 360° pattern. Module colors are available in Black, Gray, and White. Module is cut for round pole mounting. Pole diameter is needed upon order. Poles to be drilled in the field will be provided with installation instructions. Ordering Example: SCL-R44/2772/BL3 Square Pole-Mounted Occupancy Sensor up to 16' SCL-S Square Pole-Mounted Occupancy Sensor up to 16’ - an outdoor occupancy sensor with 0-10V interface dimming control that mounts directly to the pole. Wide 360° pattern. Module colors are available in Black, Gray, and White. Module is cut for square pole mounting. Pole diameter is needed upon order. Poles to be drilled in the field will be provided with installation instructions. Ordering Example: SCL-L/2772/BL3 Round Pole-Mounted Occupancy Sensor 16’ to 30’ SCH-R Round Pole-Mounted Occupancy Sensor: 16' to 30’ - an outdoor occupancy sensor with 0-10V interface dimming control that mounts directly to the pole. Wide 360° pattern. Module colors are available in Black, Gray, and White. Module is cut for round pole mounting. Pole diameter is needed upon order. Poles to be drilled in the field will be provided with installation instructions. Ordering Example: SCH-R44/2772/BL3 Square Pole-Mounted Occupancy Sensor 16’ to 30’ SCH-S Square Pole-Mounted Occupancy Sensor: 16 to 30’ - an outdoor occupancy sensor with 0-10V interface dimming control that mounts directly to the pole. Wide 360° pattern. Module colors are available in Black, Gray, and White. Module is cut for round pole mounting. Pole diameter is needed upon order. Poles to be drilled in the field will be provided with installation instructions. Ordering Example: SCH-S/2772/BL3 SCP The SCP is a photo-control with motion sensing accessory thats mounts to the side of any new or existing 3”-5” round or square straight pole. The SCP enables any pole mounted luminaire in excess of 75 watts, to meet California Title 24 requirements with integral 20KV/10KA surge protection for added reliability and serviceability. For more detail: http://www.aal.net/products/sensor_control_ programmable 2Voltage, 3Color, 4Pole Diameter 1 PRECOMMISSIONED SITESYNC ORDERING INFORMATION: When ordering a fixture with the SiteSync lighting control option, additional information will be required to complete the order. The SiteSync Commissioning Form or alternate schedule information must be completed. This form includes Project location, Group information, and Operating schedules. For more detailed information please visit www.HubbellLighting.com/products/sitesync or contact Hubbell Lighting tech support at (800) 345-4928. SiteSync fixtures with occupancy sensor (SWPM) require the mounting height of the fixture for selection of the lens. Examples: SiteSync only : ALT3/P70/60L/3KUV/PS/US/SWP SiteSync with Motion Control: ALT3/P70/60L/3KUV/PS/US/SWPM-20F MOB ORDERING INFORMATION: When ordering a fixture with a dimming occupancy sensor option (MOB), please specify the appropriate information. These settings are specified in the ordering as shown in the example below. ALT3/P70/60L/3KUV/PS/US/MOB - 1 to 30 min - 33%or 50% - ?? / DBT High to Dim Delay Low Level Mounting Height (ft.) 2Voltage, 3Color, 4Pole Diameter 1 PRECOMMISSIONED SITESYNC ORDERING INFORMATION: When ordering a fixture with the SiteSync lighting control option, additional information will be required to complete the order. The SiteSync Commissioning Form or alternate schedule information must be completed. This form includes Project location, Group information, and Operating schedules. For more detailed information please visit www.HubbellLighting.com/products/sitesync or contact Hubbell Lighting tech support at (800) 345-4928. SiteSync fixtures with occupancy sensor (SWPM) require the mounting height of the fixture for selection of the lens. Examples: SiteSync only : ALT3/P70/60L/3KUV/PS/US/SWP SiteSync with Motion Control: ALT3/P70/60L/3KUV/PS/US/SWPM-20F MOB ORDERING INFORMATION: When ordering a fixture with a dimming occupancy sensor option (MOB), please specify the appropriate information. These settings are specified in the ordering as shown in the example below. ALT3/P70/60L/3KUV/PS/US/MOB - 1 to 30 min - 33%or 50% - ?? / DBT High to Dim Delay Low Level Mounting Height (ft.) | 5 | Kim Lighting reserves the right to change specifications without notice. SAR The Archetype® Small PicoPrism LED kl_sarpled_spec.pdf © 2017 KIM LIGHTING | 17760 Rowland Street | City of Industry | CA 91748 P 626.968.5666 | F 626.369.2695 | www.kimlighting.com | Rev. Apr 23, 2019 Wall Mounting: ■Fixture mounts to 3" or 4" junction boxes by a cast aluminum adapter plate with fixture mounting bolts. NOTE: Junction box in wall must provide adequate fixture support. See NEC sections 370-13, 17 and 410-14, 16. Quick-disconnect plug and wiring are provided to allow field connections prior to fixture mounting. Horizontal Slipfitter Mount: ■ Replaces standard mounting arm with a slipfitter which allows fixture to be mounted to a horizontal pole davit-arm with 2" pipe-size mounting end (2 3/8" O.D.). Cast aluminum slipfitter with set screw for an up or down 5° adjustment lock. Bolts to housing from inside the electrical compartment using mounting holes for the standard support arm. Davit-arm must be field drilled at a set screw location to insure against fixture rotation. Finished to match fixture. Vertical Slipfitter Mount: ■ Allows fixture with standard support arm to be mounted to poles having a 2" pipe-size tenon (2 3/8" O.D. x 4 1/2" min. length). All mount- ing configurations can be used (1SA, 2SB, 2SL, 3ST, 3SY, 4SC). 4" square or round die-cast aluminum with flush cap, secured by four 3/8" stainless steel set point allen screws, finished to match fixture and arm. NOTE: 3SY only available on round slipfitter. Neighbor Friendly Optic ■ Integrated Neighbor Friendly Optic on each PicoEmitter™ module to completely control unwanted backlight. Most effective with Type III and IV distibutions. Tamper-Resistant Latch ■ Standard die-cast latch is provided with a captive 10-32 stainless steel flat socket-head screw to prevent unauthorized opening. NOTE: Required only for vandal protection in locationswhere fixtures can be reached by unauthorized persons. OPTIONS Vertical Slipfitter Mount by Kim Pole with 2" pipe-size tenon (by others) stainless steel set screws Round Square Cat. No. VSF-1SA VSF-2SB VSF-2SL VSF-3ST VSF-3SY VSF-4SC Cat. No. SVSF-1SA SVSF-2SB SVSF-2SL SVSF-3ST SVSF-4SC Mounting Configuration 1SA - single arm mount 2SB - 2 at 180° 2SL - 2 at 90° 3ST - 2 at 90° 3SY - 2 at 120° 4SC - 2 at 90° Davit-arm with 2" pipe-size fixture mount (by others) Horizontal Slipfitter Mount by Kim 11/16" 43/4" J-box Wall mount using adapter plate 3" or 4" J-box in wall (by others) 280LOW LEVEL Site Lightforms Bollard SL1 FIXTURE SL1 Site Lightforms FIXTURE FINISH BL Black DB Dark Bronze LG Light Gray TT Titanium PS Platinum Silver WH White CC Custom Color* *Consult representative 18L LEDs5 36L LEDs5 ELECTRICAL MODULE SL1 ORDERING. INFORMATION (Example) SL1 WH18L3K120 LED Color Temperature 2K Amber 3K 3000K 4K 4000K 5K 5000K FEATURES • SL1 is specifi cally designed and engineered to combine contemporary form with rugged cast aluminum vandal resistant construction • SL1 offers path lighting with IDA approved full-cutoff optics • One-piece extruded aluminum shaft for a clean sharp cornered appearance with superior strength • Battery back-up, emergency battery pack and houseside shield options SL1 SITE LIGHTFORMSMaximum weight: 37 lb SL2 SITE LIGHTFORMSMaximum weight: 47 lb FRONT SIDE FRONT SIDE 8"(203 mm)8E"(225 mm)8"(203 mm)3B"(79 mm) 42"*(1067 mm) 4K"(114 mm) BASE PLANSL1*36" OVERALL HEIGHTAVAILABLE - CONTACT KIM REPRESENTATIVE 8"(203 mm) 8K" (216 mm) BOLT CIRCLE DIA. 9D"(245 mm) 37K"(953 mm)LIGHTCENTERHEIGHT 42"*(1067 mm) 4K"(114 mm) BASE PLANSL2*36" OVERALL HEIGHTAVAILABLE - CONTACT KIM REPRESENTATIVE 8"(203 mm) 8K" (216 mm) BOLT CIRCLE DIA. 9D"(245 mm) 37K"(953 mm)LIGHTCENTERHEIGHT 21"(533 mm)8"(203 mm)8E"(225 mm) 3B"(80 mm) Voltages UV Universal Voltage(120 thru 277) 3000K and warmer CCTs only The Halo RL560 is a complete LED Baffle-Trim Module for 5" and 6" aperture recessed downlights; suitable for new construction, remodel and retrofit installation. The RL560 is cULus Listed for use with Halo and All-Pro, and is UL Classified for use with other compatible 5" and 6" housings. The RL560 with integral LED driver offers 120 volt dimming capability. The RL560 lens provides uniform illumination and wet location listing. Precision construction makes any housing AIR-TITE for added HVAC savings and code compliance. Compliant with NFPA 70, NEC section 410.16 (A)(1) and 410.16 (C)(3). RL560WH9† White MECHANICAL Module - Trim • Module construction includes LED, heat sink, reflector, lens, baffle and trim ring • Regressed baffle • Heat sink designed to conduct heat away from the LED keeping the junction temperatures below specified maximums, even when installed in insulated ceiling environments. L70 at 50,000 hours. • Designer trim finish options (sold separately) • White (Paintable) Trim Ring • Satin Nickel Trim Ring • Tuscan Bronze Trim Ring Lens • Regressed lens • Impact-resistant polycarbonate • Convex form for lamp-like appearance • High lumen transmission • Diffusing for even illumination Mounting • Integral torsion springs and Push-N-Twist clips offer two mounting options • Torsion springs are pre-installed and adjust to fit 5" or 6" compatible housings • Push-N-Twist universal installation clips are pre-installed and designed to fit 5" or 6" compatible housings Housing Compatibility See Housing Compatibility LED • Color Temperature (CCT)† Options: • 90 CRI: 2700K, 3000K, 3500K, 4000K, and 5000K • Can be used to comply with California Title 24 High Efficacy requirements. Certified to California Appliance Efficiency Database under JA8. LED Chromaticity • A tight chromaticity specification ensures LED color uniformity, sustainable Color Rendering Index (CRI) and Correlated Color Temperature (CCT) over the useful life of the LED • LED chromaticity of 3 SDCM exceeds ENERGY STAR® color stan-dards per ANSI C78.377-2008 • High color performance with R9 greater than 50 • Every Halo LED is quality tested, measured, and serialized in a permanent record to register lumens, wattage, CRI and CCT • Halo LED serialized testing and measurement ensures color and lumen consistency on a per-unit basis, and validates long-term product consistency over time ELECTRICAL Power Connections • LED connector is a non-screw base luminaire disconnect offering easy installation with the matching Halo 5" and 6" LED housings • LED Connector meets California Title-24 high efficacy luminaire requirement for a non-screw base socket, and where required to qualify as a high efficacy luminaire • The included E26 medium screw-base Edison adapter provides easy retrofit of incandescent housings (see Housing Compatibility) Ground Connection Separate grounding cable included on the module for attachment to the housing during installation. LED Driver • Dimmable driver is a 120 Volt, high efficiency, electronic power supply providing DC power to the LED • Driver meets FCC EMI/RFI Consumer Level limits for use in residential and commercial installations • Driver features high power factor, low THD, and has integral thermal protection in the event of over temperature or internal failure Dimming • Designed for continuous dimming capability to nominally 5% with many 120V Leading Edge (LE) and Trailing Edge (TE) Phase Control dimmers. (Dimmers with low end trim adjustment offer greater assurance of achieving 5% level.) • Consult dimmer manufacturer for compatibility and conditions of use Note: some dimmers require a neutral in the wallbox. Warranty Eaton provides a five year limited warranty on RL56 LED. Compliance Labels • UL Certified 1598 Luminaire with Halo housings and others - see Housing Compatibility • UL Certified for Damp Location • IP56 Ingress Protection rated • May be installed in housings in direct contact with insulation** and combustible material Compliance • Airtight certified per ASTM E283 (not exceeding 2.0 CFM under 75 Pascals pressure difference) • 90 CRI: Can be used to comply with California Title 24 High Efficacy requirements. Certified to California Title 20 Appliance Efficiency Database.* • 80 CRI: Can be used to comply with California Title 24 Non-Residential Lighting Controls requirements as an LED luminaire • Can be used for International Energy Conservation Code (IECC) high efficiency luminaire compliance • Can be used for Washington State Energy Code compliance • ENERGY STAR® Certified luminaire - consult ENERGY STAR® Certified Product List* • EMI/RFI per FCC 47CFR Part 15 Class B Consumer limits, suitable for use in residential and commercial installations • Contains no mercury or lead and RoHS compliant • Photometric testing in accordance with IES LM-79 • Lumen maintenance projections in accordance with IES LM-80 and TM-21 • Suitable for use in closets. Compliant with NFPA 70, NEC Sec. 410.16 (A)(1) and 410.16 (C)(3). Specification Features Description 900 Series 5/6-Inch LED Recessed Retrofit Module-Trim 90CRI 2700K, 3000K, 3500K, 4000K, 5000K FOR USE IN INSULATED CEILING AND NON- INSULATED CEILING RATED HOUSINGS HIGH EFFICACY LED WITH INTEGRAL DRIVER - DIMMABLE Refer to ENERGY STAR® Qualified Products List.Can be used to comply with California Title 24 High Efficacy requirements.Certified to California Appliance Efficiency Database under JA8. * Refer to ENERGY STAR® Certified Products List and CEC (T20) Appliance Database for listings. ** Not for use with housings in direct contact with spray foam insulation. † See ordering information table for available models. Catalog #Type Project Comments Date Prepared by HALO® TD518005EN October 23, 2017 3:55 PM Ordering Information Sample Number: RL560WH9927-RL56TRMSNB Complete unit includes a RL56 Baffle-Trim LED Module and a 5" and 6" compatible housing (ordered separately). Optional accessory designer trim ring ordered separately. RL56 900 Series Accessory (Order Separately) RL560WH9927=5"/6" Retrofit Baffle - Trim LED Module, 90CRI, 2700K, Matte White RL560WH9930=5"/6" Retrofit Baffle - Trim LED Module, 90CRI, 3000K, Matte White RL560WH9935=5"/6" Retrofit Baffle - Trim LED Module, 90CRI, 3500K, Matte White RL560WH9940=5"/6" Retrofit Baffle - Trim LED Module, 90CRI, 4000K, Matte White RL560WH9950=5"/6" Retrofit Baffle - Trim LED Module, 90CRI, 5000K, Matte White RL56TRMSNB=5/6" Satin Nickel Trim Ring, Baffle RL56TRMTBZB=5/6" Tuscan Bronze Trim Ring, Baffle RL56TRMWHB=5/6" White Paintable Trim Ring, Baffle RL56TRMSN=5/6" Satin Nickel Trim Ring RL56TRMTBZ=5/6" Tuscan Bronze Trim Ring RL56TRMWH=5/6" White Paintable Trim Ring OT400P=Oversize Flat White Metal Trim Ring 6" I.D. x 9-1/4" O.D. (ring slips behind RL56 ring, in stepped configuration) OT403P=Oversize White Plastic Trim Ring 6" I.D. x 8" O.D. (ring slips behind RL56 ring, in stepped configuration) TRM690WH=Oversize Matte White Metal Trim Ring. Designed for RL560 ring to inset into oversize ring for an even (non-stepped) trim surface HE26LED=Replacement screw base adapter (one included with unit) E26 Screw base adapter for retrofit (included) RL56 Dimensions Energy Data RL56 Series (Values at non-dimming line voltage) Minimum Starting Temp: -30°C (-22°F) EMI/RFI: FCC Title 47 CFR, Part 15, Class B (Consumer) Sound Rating: Class A Input Voltage: 120V Power Factor: >0.90 Input Frequency: 60Hz THD: <20% Input Power: 13.5W Input Current: 0.15A Maximum IC (Insulated Ceiling) Ambient Continuous Operating Temperature: 25°C (77°F) Maximum Non-IC Ambient Continuous Operating Temperature 40°C (104°F) Designer Trim Dimensions RL56TRMWHB White (Paintable) RL56TRMSNB Satin Nickel RL56TRMTBZB Tuscan Bronze 0.86"[21.8mm] 7.35"[186.7mm] 7.25” [184.15mm]2.33” [59.22mm] 7.35" [186.7mm] 0.86" [21.8mm] RL56TRMWH White (Paintable) RL56TRMSN Satin Nickel RL56TRMTBZ Tuscan Bronze page 2 RL56 LED System 900 Series Eaton1121 Highway 74 SouthPeachtree City, GA 30269P: 770-486-4800www.eaton.com/lighting Specifications and dimensions subject to change without notice. RL56 Series LED Retrofit is UL Classified for retrofit in the follow 5/6" recessed housings: The RL Series LED light module - trim combination is UL Certified for use with any 5"/6" diameter recessed housing constructed of steel or aluminum with an internal volume that exceeds 107.9 in3 in addition to those noted above. Housing Compatibility Compatible Halo LED Housings with LED luminaire connector (high-efficacy compliant) HALO LED Recessed Can Size Catalog Number 5"H550ICAT, H550RICAT, E550ICAT, E550RICAT 6"H750ICAT, H750RICAT, H750T, H750RINTD010, H750TCP, H2750ICAT, H2750RICAT, E750ICAT, E750RICAT Halo LED Retrofit Enclosures HALO 6"ML7BXRFK, ML7E26RFK Compatible Halo Incandescent E26 Screwbase Housings HALO 5"H5ICAT, H5RICAT, H5ICATNB, H5T, H5RT, H25ICAT, H25ICATNB, E5TAT, E5RTAT, H5TNB, E5TATNB, E5ICAT, E5RICAT, E5ICATNB 6"H7ICAT, H7RICAT, H7ICT, H7RICT, H7ICATNB, H7ICTNB, H7T, H7RT, H7TNB, H7TCP, H7UICT, H7UICAT, H27ICAT, H27RICAT, H27T, H27RT, E7ICAT, E7RICAT, E27ICAT, E27RICAT, E7ICATNB, E7TAT, E7RTAT, E7TATNB, E27TAT, E27RTAT Product and Photometric Data RL56-900 Series Photometric* RL560WH9930 Luminaire lumens 930 Input watts 12.8 LER (LPW)72.7 Spacing Criteria 0-180 1.16 90-270 1.16 Diagonal 1.22 Beam angle (degrees)88.9 Field angle (degrees)140 Zonal lumen Lumens % Lumens 0-30 341 36.7 0-40 535 57.5 0-60 829 89.1 0-90 930 100 * Tested in accordance with IES LM63. Field results may vary. RL56 - 900 SERIES Cat No. CRI CCT Lumens Power (W)LPW RL560WH9927 92 2700 940 12.6 75 RL560WH9930 91 3000 930 12.8 73 RL560WH9935 92 3500 940 12.7 74 RL560WH9940 90 4000 1000 13.2 76 RL560WH9950 90 5000 1015 12.9 79 page 3 RL56 LED System 900 Series Eaton1121 Highway 74 SouthPeachtree City, GA 30269P: 770-486-4800www.eaton.com/lighting Specifications and dimensions subject to change without notice. LIGHTING FACTS RL560WH99272700K Source RL560WH9950 5000K Source RL560WH99303000K Source RL560WH99353500K Source RL560WH99404000K Source Eaton1121 Highway 74 SouthPeachtree City, GA 30269P: 770-486-4800www.eaton.com/lighting Specifications and dimensions subject to change without notice. page 4 RL56 LED System 900 Series ADV141506 6/17/2014 Catalog # Project Comments Prepared by Type Date HALO LED ICAT SHALLOW HOUSING for NEW CONSTRUCTION The H2750ICAT is a dedicated LED new construction housing for use in shallow ceilings where 2x6 joist construction is used.The H2750ICAT is designed to fit in shallow insulated ceilings and can be in direct contact with ceiling insulation*. This AIR-TITE housing design prevents airflow between conditioned and unconditioned spaces for savings on both heating and air conditioning costs. The LED connector system provides high efficacy code compliance when used with designated HALO LED modules and trims. Housings • Aluminum housing for greater heat dissipation. H2750ICAT housing is gasketed to prevent airflow from heated or air conditioned spaces Plaster Frame • Galvanized steel frame. Housing adjusts in plaster frame to accommodate up to 1-3/8” ceiling thickness. • Regressed locking screw for securing hanger bars. • Cutouts included for easily crimping hanger bars in position. Slide-N-Side™ Junction Box • Positioned to accommodate straight conduit runs. • Seven ½” trade size conduit knockouts with true pry-out slots. • Slide-N-Side wire traps allow non metallic sheathed cable to be installed without tools and without removing knockouts. • Allows wiring connections to be made outside the box. • Simply insert the cable directly into the trap after connections are made. • Accommodates the following standard non-metallic sheathed cable type: • U.S. #14/2, #14/3, #12/2, #12/3 • Canada: #14/2, #14/3, #12/2 GOT NAIL! Pass -N-Thru™ Bar Hangers Bar Hanger features include • Pre-installed nail easily installs in regular lumber, engineered lumber and laminated beams. • Safety and Guidance system prevents snagging, ensures smooth, straight nail penetration and allows bar hangers to be easily removed if necessary • Automatic leveling flange aligns the housing and allows holding the housing in place with one hand while driving nails. • Housing can be positioned at any point within 24” joist spans • Score lines allow tool-free shortening for 12” joists and bar hangers do not need to be removed for shortening. • Bar hangers may be repositioned 90° on plaster frame • IntegralT-bar clip snaps onto T-bars – no additional clips are required. LED Module Connection Halo shallow LED modules simply install with a plug-in 120V/277V rated line voltage wiring connector (UL and CSA Listed Luminaire Disconnect). This non-screw-base connection preserves the high efficacy rating and prevents use of low effi- cacy incandescent sources (see LED Module specifications). Caution LED connection is rated for 120V and 277V input. Installer must verify LED module voltage is compatible with the applicable voltage input. If uncertain, consult a qualified electrician. Labels • UL/cUL Listed 1598 Luminaire • CE Marking - “Conformité Européene” conformity with the Council of European Communities Directives, meeting internationally recognized compliance when used with ML56 Series LED modules • UL/cUL Listed for Feed Through • UL/cUL Listed for Damp Location • UL/cUL Listed forWet Location with select trims • UL/cUL Listed fro direct contact with insulation and combustible material* • Rated for 20W maximum Qualification May be used with qualified Halo LED modules and designated trims for High Efficacy Luminaire Compliance: • State of California Title 24 • International Energy Conservation Code (IECC) • Washington State Energy Code • New York State Energy Conservation Construction Code - AIR-TITE™ Compliant • Certified under ASTM-E283 standard for air-tight construction DESIGN FEATURES H2750ICAT 6” New Construction IC AIR-TITE™ Housing For Designated Halo LED Modules and Trims -RA56 Series -RL56 Series -ML56 Series High Efficacy LED Housing HALO® FOR USE IN INSULATED CEILINGS FOR DIRECT CONTACT WITH INSULATION* FOR USE IN SHALLOW CEILINGS 6-1/2"[165mm] 1/2"[13mm] 5"[127mm] 7-1/2"[191mm] 10-1/2"[267mm] * Not to be used in direct contact with spray foam insulation. Can be used with Qualified and compliant with select trims. Refer to ENERGY STAR® Qualified Products List and CEC (T24) Appliance Database for listings. Eaton1000 Eaton BoulevardCleveland, OH 44122United StatesEaton.com Specifications and dimensions subject to change without notice. Eaton’s Cooper Lighting Business 1121 Highway 74 SouthPeachtree City, GA 30269P: 770-486-4800www.cooperlighting.com © 2014 EatonAll Rights ReservedPrinted in USAPublication No. ADV141506June 2014 H2750ICAT ORDERING INFORMATION - RL56 SERIES SAMPLE NUMBER: H2750ICAT - RL560WH6927 Order housing, light module, trim and separately. Housing RL56 Series - Compatible LED Retrofit Modules H2750ICAT= 6” Dedicated LED Insulated Ceiling, AIR-TITE New Construction Housing for Shallow Ceilings 80 CRI RL560WH6827= 5”/6” Retrofit Baffle - Trim LED Module, 80CRI, 2700K, Matte White RL560SN6827= 5”/6” Retrofit Baffle - Trim LED Module, 80CRI, 2700K, Satin Nickel RL560WH6830= 5”/6” Retrofit Baffle - Trim LED Module, 80CRI, 3000K, Matte White RL560SN6830= 5”/6” Retrofit Baffle - Trim LED Module, 80CRI, 3000K, Satin Nickel RL560WH6835= 5”/6” Retrofit Baffle - Trim LED Module, 80CRI, 3500K, Matte White 90 CRI RL560WH6927= 5”/6” Retrofit Baffle - Trim LED Module, 90CRI, 2700K, Matte WhiteRL560SN6927= 5”/6” Retrofit Baffle - Trim LED Module, 90CRI, 2700K, Satin NickelRL560WH6930= 5”/6” Retrofit Baffle - Trim LED Module, 90CRI, 3000K, Matte WhiteRL560SN6930= 5”/6” Retrofit Baffle - Trim LED Module, 90CRI, 3000K, Satin NickelRL560WH6935= 5”/6” Retrofit Baffle - Trim LED Module, 90CRI, 3500K, Matte White ORDERING INFORMATION - RA56 SERIES SAMPLE NUMBER: H2750ICAT - RA5606927WHOrder housing, light module, trim and separately. Housing RA56 Series - Compatible LED Retrofit Modules H2750ICAT= 6” Dedicated LED Insulated Ceiling, AIR-TITE New Construction Housing for Shallow Ceilings Very Wide Flood - VWFL Models RA5606927WH= 5”/6” LED Adjustable Gimbal, 90CRI, 2700K, White, Very Wide FloodRA5606930WH= 5”/6” LED Adjustable Gimbal, 90CRI, 3000K, White, Very Wide Flood Narrow Flood - NFL Models RA5606927NFLWH= 5”/6” LED Adjustable Gimbal, 90CRI, 2700K, White, Narrow FloodRA5606930NFLWH= 5”/6” LED Adjustable Gimbal, 90CRI, 3000K, White, Narrow Flood ORDERING INFORMATION - ML56 SERIES SAMPLE NUMBER: H2750ICAT - ML5606830 - 696WBOrder housing, light module, trim and separately. Housing ML56 LED Light Modules ML56 LED Trims ML56 System Accessories H2750ICAT= 6” Dedicated LED Insulated Ceiling, AIR-TITE New Construction Housing for Shallow Ceilings 600 Series / 80 CRIML5606827= 5"/6" LED Retrofit Downlight Light Module, 600 lumen, 80CRI, 2700KML5606830= 5"/6" LED Retrofit Downlight Light Module, 600 lumen, 80CRI, 3000KML5606835= 5"/6" LED Retrofit Downlight Light Module, 600 lumen, 80CRI, 3500KML5606840= 5"/6" LED Retrofit Downlight Light Module, 600 lumen, 80CRI, 4000K 600 Series / 90 CRIML5606927= 5”/6” LED Retrofit Downlight Light Module, 600 lumen, 90CRI, 2700KML5606930= 5”/6” LED Retrofit Downlight Light Module, 600 lumen, 90CRI, 3000KML5606935= 5”/6” LED Retrofit Downlight Light Module, 600 lumen, 90CRI, 3500KML5606940= 5”/6” LED Retrofit Downlight Light Module, 600 lumen, 90CRI, 4000K 900 Series / 80 CRIML5609827= 5”/6” LED Retrofit Downlight Light Module, 900 lumen, 80CRI, 2700KML5609830= 5”/6” LED Retrofit Downlight Light Module, 900 lumen, 80CRI, 3000KML5609835= 5”/6” LED Retrofit Downlight Light Module, 900 lumen, 80CRI, 3500KML5609840= 5”/6” LED Retrofit Downlight Light Module, 900 lumen, 80CRI, 4000K 900 Series / 90 CRIML5609927= 5”/6” LED Retrofit Downlight Light Module, 900 lumen, 90CRI, 2700KML5609930= 5”/6” LED Retrofit Downlight Light Module, 900 lumen, 90CRI, 3000KML5609935= 5”/6” LED Retrofit Downlight Light Module, 900 lumen, 90CRI, 3500KML5609940= 5”/6” LED Retrofit Downlight Light Module, 900 lumen, 90CRI, 4000K 1200 Series / 80 CRIML5612827= 5”/6” LED Light Module, 1200 lumen, 80CRI, 2700KML5612830= 5”/6” LED Light Module, 1200 lumen, 80CRI, 3000KML5612835= 5”/6” LED Light Module, 1200 lumen, 80CRI, 3500KML5612840= 5”/6” LED Light Module, 1200 lumen, 80CRI, 4000K 1200 Series / 90 CRIML5612927= 5”/6” LED Light Module, 1200 lumen, 90CRI, 2700KML5612930= 5”/6” LED Light Module, 1200 lumen, 90CRI, 3000KML5612935= 5”/6” LED Light Module, 1200 lumen, 90CRI, 3500KML5612940= 5”/6” LED Light Module, 1200 lumen, 90CRI, 4000K 690 Series - 6" LED Trims Non-Conductive “Dead Front” Baffles 691WB=6" LED Trim, Polymer “Dead- Front”, Shallow White Baffle & Flange (For use with 600 Series LED Light Modules only) Semi-Regressed Eyeballs 694WB=6" LED Directional Trim, White Eyeball, Baffle & Flange 694SNB=6" LED Directional Trim, Satin Nickel Eyeball, Baffle & Flange 694TBZB=6" LED Directional Trim, Tuscan Bronze Eyeball, Baffle & Flange Shallow Baffle 696WB=6" LED Trim, White Shallow Baffle & Flange ML56CLIP= 6” Friction Clip Kit - For use with non-torsion spring housings. 6” clips included. WW6955C= Wall Wash Insert - Specular Kick Reflector for 695WW (1 included with trim). For double wall washing or replacement. TRM690WH= 6" LED Oversize Trim Ring for use with 59* series trims, White 6.9" I.D., 9.5" O.D. Ring slips over LED trim. Inset design allows 6" trim to fit into oversize ring for an even trim surfaceEBA560PK= Replacement screwbase adapter to LED disconnect with cap ML56-1200 Series Beam Forming Optic MediaBFR56NFL=Beam forming reflector kit, narrow flood, 25° nominalBFR56MH=Media holder, accepts one 3.45” lens. Requires BFR56NFL & L345SF, order separately. L345SF=3.45” diameter soft focus lens. Requires BFR56NFL and BFR56MH, order separately. Solite® is a registered trademark of AGC Flat Glass North America. Approvals:Type:Job:Catalog number: Specifications Date:Page: 1 of 4 LED EmitterDeck® Electronic Module SAR-LED-KIT 40 Light Emitting Diodes 46 total System Watts for 350mA 93 total System Watts for 700mA Maximum Weight is 30 lbs. when installed in The Archetype LED SAR-LED-KIT The Archetype® Small PicoPrism™ LED Upgrade Kit 4/20/17 • kl_sarpledkit_spec.pdf / / LED Kit Electrical Module Option Electronic Module: All electrical components are UL and CSA recognized, mounted on a single plate and factory prewired with quick-disconnect plugs. Module includes a driver, thermal control device and surge protector. Electrical module attaches to housing with no-tool hinges and latches, accessible by opening the lens frame only. Driver is rated for -40°F starting. Optical Module: Precision, IP66 replaceable PicoPrism™ modules are positioned to achieve directional control toward desired task. The entire light engine fastens to the housing as a one-piece module Dimming: Driver has a 0-10V dimming interface with a dimming range of 10-100%. Approved dimmers include Lutron Diva AVTV, Lutron Nova NFTV and NTFTV. Note: Not compatible with current sourcing dimmers. Listed to: UL 1598 Standard for Luminaires - UL 8750 Standard for Safety for Light Emitting Diode (LED) Equipment for use in Lighting Products and CSA C22.2#250.0 Luminaires. RoHS compliant. Meets Buy American provisions within ARRA. Warranty: Kim Lighting warrants The Archetype LED products (“Product(s)”) sold by Kim Lighting to be free from defects in material and workmanship for (i) a period of five (5) years for metal parts, (ii) a period of ten (10) years for exterior housing paint finish(s), (iii) a period of six (6) years for LED Light Engines (PicoPrisms™ and, (iv) a period of five (5) years for LED power components (LED Driver, LifeShield® device), from the date of sale of such goods to the buyer as specified in Kim Lighting shipment documents for each product. Occupancy sensors, Surge Protector, dimmers and relay wiring components are covered by the manufacturer’s warranty. NOTE: Existing product conditions are taken as the base point. Participation rules apply. See complete warranty provisions for further details. IMPORTANT: Disable all power to the luminaire before conducting any maintenance or upgrade activity. Failure to do so will create a hazardous working environment. CAUTION: Fixtures must be grounded in accordance with national, state and/or local electrical codes. Failure to do so may result in serious personal injury. KIM LIGHTING RESERVES THE RIGHT TO CHANGE SPECIFICATIONS WITHOUT NOTICE. © 2017 KIM LIGHTING • 16555 EAST GALE AVENUE, CITY OF INDUSTRY, CA 91745-1788 • TEL: 626/968-5666 • FAX: 626/968-5716 US Patent Number D674,965 S. Suggested Tools: • Phillips Screw Driver • Large Flat Blade Screw Driver WARNING: PicoPrism luminaires are designed with open door frame, no lens. When installing an Upgrade Kit, the glass lens must be removed due to the increased current of the Picoprism assemblies. Reference HID to PicoPrism Upgrade Kit Installation sheet for instructions. SAR-LED-KIT Page: 2 of 4 Type: Job: Standard Features Fixture Cat. No. designates fixture and distribution Upgrade Kit: SAR-LED-KIT Light Distribution: SAR-LED-KIT The Archetype® Small PicoPrism™ LED Upgrade Kit 4/20/17 • kl_sarpledkit_spec.pdf 40L xxK Electrical Module Cat. Nos. for Electrical Modules available: 1120V through 277V is a variable driver. Source: 40L = 40 LED’s Color Temperature:l 2K = 580nm - Amber l 3K = 3000K l 4K = 4200Kl 5K = 5100K Voltage:l 120 = 120V1l 208 = 208V1l 240 = 240V1l 277 = 277V1l 347 = 347Vl 480 = 480V Distribution:l 1 = Type I l 2 = Type II l 3 = Type III l 4 = Type IV l 5 = Type V l L = Type L l R = Type R x P xx Optic: P = PicoPrism™ Current: 35 = 350 mA 70 = 700 mA © 2017 KIM LIGHTING • 17760 ROWLAND STREET, CITY OF INDUSTRY, CA 91748 • TEL: 626/968-5666 • FAX: 626/369-2695 TYPE R One-Way Right TYPE LOne-Way Left TYPE IV TYPE V TYPE IIITYPE IITYPE I Page: 3 of 4 Type: Job: Optional Features SAR-LED-KIT The Archetype® Small PicoPrism™ LED Upgrade Kit 4/20/17 • kl_sarpledkit_spec.pdf Fusing Cat. No. (see right) l No Option High temperature fuse holders factory installed inside the fixture housing. Fuse included. Line Volts: 120V 208V 240V 277V 347V 480V Cat. No.: l SF l DF l DF l SF l SF l DF Single Fuse Neighbor Friendly Optic: Cat. No. l NFO l No Option Integrated Neighbor Friendly Optic on each PicoPrism™ module to completely control unwanted backlight. Most effective with Type III and IV distibutions. Driver has a 0-10V dimming interface with a dimming range of 10-100%. Approved dimmers include Lutron Diva AVTV, Lutron Nova NFTV and NTFTV. Note: Not compatible with current sourcing dimmers. 0-10V Dimming Interface Fixture Housing LifeShield® 40 mA Max Fixture Equivalent Circuit Dimming Lead (+) Dimming Lead (-) Driver 5V © 2017 KIM LIGHTING • 17760 ROWLAND STREET, CITY OF INDUSTRY, CA 91748 • TEL: 626/968-5666 • FAX: 626/369-2695 For warranty see http://www.hubbelllighting.com/resources/warranty Page: 4 of 4 Type: Job: SAR-LED-KIT The Archetype® Small PicoPrism™ LED Upgrade Kit 4/20/17 • kl_sarpledkit_spec.pdf Lumen Data © 2017 KIM LIGHTING • 17760 ROWLAND STREET, CITY OF INDUSTRY, CA 91748 • TEL: 626/968-5666 • FAX: 626/369-2695 Absolute Lumens for 350mA Temperature Type I Type II Type III Type III NFO Type IV Type IV NFO Type V Type L/R 3000K 3747 3644 3634 3242 3727 3385 3740 3658 4200K 4536 4411 4378 3925 4512 4098 4527 4428 5100K 4930 4795 4730 4266 4904 4454 4921 4813 Absolute Lumens for 700mA Temperature Type I Type II Type III Type III NFO Type IV Type IV NFO Type V Type L/R 3000K 6247 6214 6190 5493 6239 5694 6420 6131 4200K 7912 7870 7840 6956 7902 7211 8131 7765 5100K 8220 8176 8145 7227 8209 7492 8447 8067 B.U.G. Rating for 350mA (TM15) in Lumens where B = Backlight, U = Uplight, G = Glare Temperature Type I Type II Type III Type III NFO Type IV Type IV NFO Type V Type L/R 3000K B2 U0 G2 B2 U0 G2 B1 U0 G1 B1 U0 G1 B0 U0 G2 B0 U0 G2 B3 U0 G3 B2 U0 G2 4200K B3 U0 G3 B2 U0 G2 B1 U0 G2 B1 U0 G2 B0 U0 G2 B0 U0 G2 B3 U0 G3 B2 U0 G2 5100K B3 U0 G3 B2 U0 G2 B2 U0 G2 B1 U0 G2 B0 U0 G2 B0 U0 G2 B3 U0 G3 B2 U0 G2 B.U.G. Rating for 700mA (TM15) in Lumens where B = Backlight, U = Uplight, G = Glare Temperature Type I Type II Type III Type III NFO Type IV Type IV NFO Type V Type L/R 3000K B3 U0 G3 B2 U0 G2 N/A N/A B0 U0 G2 B0 U0 G2 B3 U0 G3 B2 U0 G2 4200K B3 U0 G3 B3 U0 G3 B2 U0 G2 B2 U0 G2 B1 U0 G2 B0 U0 G2 B3 U0 G3 B3 U0 G3 5100K B3 U0 G3 B3 U0 G3 B2 U0 G2 B2 U0 G2 B1 U0 G2 B0 U0 G2 B3 U0 G3 B3 U0 G3 Electrical Drive Current 350mA 700mA Volts - AC Amps - AC System Watts Volts - AC Amps - AC System Watts 120 0.38 46 120 0.78 93 208 0.22 46 208 0.45 93 240 0.19 46 240 0.39 93 277 0.17 46 277 0.34 93 347 0.13 46 347 0.27 93 480 0.10 46 480 0.19 93 LED performance and lumen output continues to improve at a rapid pace. Log onto www.kimlighting.com to download the most current photometric files from Kim Lighting’s IES File Library. For custom optics and color temperature configurations, contact factory. Spectroradiometric 3000K Average 4200K Average 5100K Average Correlated Color Temp. CCT (K)2800K - 3175K 3800K - 4600K 4600K - 5600K Color Rendering Index (CRI)≥75 ≥70 ≥65 Power Factor >.90 >.90 >.90 Projected Lumen Maintenance* mA 50,000 hrs 100,000 hrs 350 mA 96.67%94.48% 700 mA 92.51%87.87% *Still awaiting independent third party verification